Bio-Clean F4000PZX Aqueous Parts Washer
- Stock No
- DC1488
- Manufacturer
- Bio-Clean
- Model
- F-4000-P-ZX
- Year of Manufacture
- 2000
- Serial
- 17257
- Condition
- From a working environment
- Work Envelope (WxDxH mm) [?]
- Turntable Ø 1015 x 1015
- Process Stages
- 3 - Wash, rinse and dry
- Other Info
- Load capacity: 680kg
- Location
- Our Central Warehouse, Aldridge, UK
- Weight (kgs)
- 1400 & 850
- External Dimensions (WxDxH mm) [?]
- 3,300 x 2,450 x 2,000
- Delivery Your delivery options
Description
Bio-clean F4000PZX three stage aqueous parts washer used for water based solutions. These heavy duty spray washing systems clean the dirtiest parts in just minutes with a "purifier” filtration feature to extend the life of the wash solution.
The namesake feature of these models is the "Purifier" filtration system which greatly extends the life of the washing solution. After the solution hits the parts it flows through a removable stainless “chip” basket. A deflector plate then shunts the solution to the rear of the tank where most of the fine sediment is trapped in a 2” deep by 10” wide canal that spans the width of the machine.
A radical floor pitch from front to back further influences the sediment toward the rear. To extract the sediment, simply remove the rear cover plates and dredge out the canal. Floating oils are continuously removed with the OSW-11 skimming system and channelled into a removable container.
This ZX model has a removable upper parts basket which doubles the cleaning capacity for small parts. The pump size is increased in some cases and the spray manifolds are modified so that both baskets are sprayed from the bottom, top, and sides. To clean tall parts, remove the ZX configuration and rotate the lower overhead pipe out of the way.
- Weight Capacity of Upper Basket: 90kg
- Work Height for upper Basket: 430mm
Front Loading Models
- 55% of the turntable is exposed, allowing a hoist chain to be positioned over the centre of the turntable.
- Turntable surface is within 30" of the ground .
- Door is supported with a continuous hinge (full length of the door).
- Door bottom is pitched to direct all residual water back to the tank.
- Labyrinth seal prevents water from escaping.
- Snap-on gasket seals in steam.
Load Bearing/Safety
- Parts are loaded directly on the turntable (basket does not have to be rolled in and out of the cabinet).
- Turntable is mounted on a structural beam tied directly to the ground (the door bears none of the load and the load is never suspended or cantilevered).
Vertical (Seal-less) Pumps
- All pumps are vertical (seal-less) style units (designed to withstand abrasive particles up to ¼" in dia.).
- There are no bearings or seals beneath the solution level.
- Driven with TEFC motors.
- Motors have extended shafts that connect directly to the impeller (no couplings).
Turntable/ Basket/ Drive System
- Centre bearing spindle is completely sealed.
- External grease cup for the bearing assembly.
- Turntable rim and spokes have a minimum thickness of 3/16”.
- Friction drive system… foam filled tire spring loaded against turntable rim.
- TEFC drive motor.
- Removable parts basket (6" high side walls/1" open mesh).
Spray Manifolds
- Stainless steel "V" jet spray nozzles.
- Manifolds positioned above, below, and on the outside of the turntable.
- Front loading models have a mid-level, overhead spray manifold that pivots out of the way for tall parts.
- On top loading models, overhead manifolds retract with the lid.
Control System
- Nema 12 control panel and junction boxes.
- 110 V controls .
- Timer for wash, rinse, and dry stages.
- Panel mounted thermostats with digital read-out for all heated circuits.
- Control and power circuits fused.
- 2 channel, 7 day/24 hour timer for water heaters and oil skimmer.
- Jog button for turntable •Door/lid safety switch.
- Terminal ends of all wires are numbered.
Inside Working Dimensions:
- Height: 1015mm
- Turntable: Ø 1015
- Turntable area: 0.8m²
Additional Specification
- Overall dimensions (WxDxH): 1600mm x 1830mm x 1830mm
- Tank size: 636 Litre
- Turntable weight capacity: 680kg
- Standard power source: 230V, 3 phase
- Full load amps: 65
- Heat source: Electric
- Heat up time: 1.5 hr
Pump Motor:
- Type: Vertical
- Size: 7.5 HP
- Output: 100 GPM/60 PSI
Onsite Data Collection
- PM712-166 - Aqueous parts washer
- OEM - Bio Clean Equipment Ltd
- Model - F4000PZX
- Serial - 17257
- Year of manufacture - 09/00
- Footprint (WxDxH) - 3300mm x 2450mm x 2000mm
- Main unit (WxDxH) - 1900mm x 2450mm x 2000mm
- Tank (WxDxH) - 1350mm x 1400mm x 1800mm
- Mains supply - 400 v 3phase 50 Hz
- Control supply 120 v
- Power - 42.8 KVA
- BOM No - 17257
Condition
- Internal stainless steel wetted area good condition.
- External mild steel/clad over insulation poor condition in parts.
This machine was working in Chromalloy's factory in Derby prior to professional removal in March 2023. As seen in the photographs there is corrosion to the external metal work.
Print / Download Bio-Clean F4000PZX Aqueous Parts Washer Datasheet
Photographs taken prior refurbishment. Our refurbishment service is not available on all machines.
Machines & equipment for sale
- Surface Treatment
- Cleaning & Degreasing
- Polishing & Belt Linishing
- Mass Finishing
- Ovens & Furnaces
- Process Cooling
- Shot Blasting
- Dust & Fume Extraction
- Air Compressors
- Rectifiers & Transformers
- Miscellaneous
- Latest Stock
- Special Offers
- Direct From Site Clearances
- Auctions
- Brand New Machines
- Available Immediately
- Sell Your Machine
Machine Alert
Get the latest machines emailed directly to you as they become available to buy online. Sign Up Now